The MG01 PRO is the track-focused version of our lightweight MG01 magnesium wheel designed for the street. The MG01 PRO is enhanced with a set of changes made specifically for track use. In this article, we'll walk you through the behind-the-scenes story of developing the MG01 PRO, the changes we made, and how we engineered and optimized the wheel for track use. The MG01 PRO is also available in a centerlock configuration for cars equipped with centerlock systems.

-2.jpg)
Early in the MG01's development, we worked with a professional driver to stress-test the wheels on his Porsche 991.2 911 T. The wheels were pushed to their limit by the driver at Homestead-Miami Speedway, a 1.5-mile oval and road-course motorsports facility located at One Ralph Sanchez, Homestead, Florida. After a few track days, some cracks initially formed on the rear wheels, starting on the back side of the spokes. Over time, those cracks spread fully through some of the spokes. The driver was able to safely stop the car in the pit lane to inspect the wheels.
After getting the failed wheels back and reviewing the incident, we determined that the main cause was repeated impact force from the suspension. A high-speed, sweeping right-hand curve combined with an elevation change caused the suspension to bottom out and transfer the impact force directly to the wheels for over a dozen laps. The impact force caused the cracks to form, and repeated impacts led to the final failure. Even though the failure wasn’t caused by cornering fatigue, this isn’t acceptable for wheels intended for heavy-duty track use. We know that when most drivers invest thousands of dollars into track equipment, how long the parts last matters just as much as the performance they deliver. So we started looking for ways to make the MG01 more durable for serious track duty while keeping the weight penalty to a minimum.

Magnesium's mechanical properties are very different from those of forged aluminum. It is a less durable metal than forged 6061-T6 aluminum. Where it really excels is weight savings: a forged magnesium wheel can achieve the same load rating as an aluminum wheel while weighing less (about 70% of the weight of equivalent aluminum wheels). We found that an aluminum wheel design cannot simply be made in magnesium. Adapting it requires design changes and additional engineering work for safe road use.

Apart from the obvious wheel damage, we noticed early-stage microcracks on the back of some of the other spokes, which matched the results of the FEA (finite element analysis) testing we had performed. The FEA indicated that, under excessive loading conditions, this area experiences high stress because it is at the turning point of the spoke’s curvature. However, that analysis didn't account for the repeated vertical impact force seen in this specific situation, since TÜV test standards are designed for road driving, not track duty.

Based on what we saw in real-world use and in our test results, we improved the original MG01 to make it much more durable for track use. Here are the changes we made for this case:
- Increased load rating. The front wheel load rating went up from 690 kg (1,520 lbs) to 750 kg (1,653 lbs), compared to a required minimum of 385 kg (844 lbs) for the 911 T. The rear wheel load rating went up from 690 kg (1,520 lbs) to 900 kg (1,984 lbs), compared to a required minimum load rating of 595 kg (1,312 lbs). The outgoing MG01 PRO models now all have a default load rating of 950 kg for longevity, unless a client requests a lower load rating to save weight.
- Reinforced spoke side-cut detail. We added a spoke support detail to relieve the stress in these areas while keeping the added weight to a minimum.

- Simplified spoke detail with reinforcement. Based on our FEA results, we removed the slotting on the main spoke branch. That area can develop high mechanical stress from lateral forces in tight-radius corners.

- New weight-reduction spoke hollowing design. Instead of cutting all the way through the spokes, we left the back side of each spoke solid for added structural integrity. We kept the hollowing on the front side for weight reduction.

We ran static tests to study the stress points. Once those stress points were optimized, we ran cornering fatigue tests to validate the final design. Clients around the world are putting in serious track time on MG01 PRO wheels.


The MG01 PRO is a significant step up in terms of track-use durability over the original MG01. The extra material does add a slight weight penalty, making it 10–15% heavier than the MG01, but it is still significantly lighter than comparable aluminum wheels. In this case study, the MG01 went from 17lbs in the front, 18.8lbs in the rear to MG01 PRO 18.7lbs in the front and 21.4lbs in the rear. If you're a hardcore track enthusiast who plans to run your wheels for years to come, the MG01 PRO is a great way to extend the life of your investment.

.jpeg)
If you are interested in getting a set of lightweight forged magnesium wheels for your vehicle, give us a call at +1 (866) 637-7222 or email us at hello@forgelitewheels.com.